
For an Indian auto component supplier, a rejection from an OEM is never just a quality problem. Parts stop at the customer's line, the supplier quality engineer is on the phone within the hour, sorting teams have to be sent, a debit note follows, an 8D is due within days, and the month's PPM figure — which feeds the supplier rating and future business — has just moved in the wrong direction.
This guide walks through the full cycle of handling an OEM customer rejection, from the first call to closure, and explains which records make each step faster and less painful. It complements our guides to 8D problem solving and customer complaint handling, focusing on what is specific to supplying OEMs.
The cycle of a customer rejection
- The complaint arrives — line rejection, incoming inspection rejection or field failure.
- Containment — suspect stock is identified, held and sorted everywhere it could be.
- Returned material and debit notes are handled.
- Root cause is found and verified.
- Corrective and preventive actions are implemented and checked.
- The 8D report is submitted and closed with the customer.
- Lessons are carried into control plans, PFMEA and inspection.
Most suppliers handle steps 4 to 6 reasonably well because the customer insists on an 8D. Where time and money are usually lost is in steps 1 to 3 — finding out what was shipped, from which lots, and getting it contained fast.
Step 1: Capture the complaint properly
Complaints arrive by email, portal, phone call or a visit from the customer's quality engineer. Whatever the channel, record the same facts in one place:
- Customer, plant and the customer's complaint or reference number.
- Part number, drawing revision and the defect described, with the customer's photos.
- Where it was found — incoming inspection, assembly line, end-of-line test or field.
- Quantity found defective and quantity checked.
- Lot, batch or date codes on the rejected parts and packaging labels.
- The customer's deadline for containment and for the 8D.
The lot or date code is the key that unlocks everything else. If your packaging labels carry a lot number linked to production records, the next steps are fast. If they don't, containment means sorting everything.
Step 2: Contain — fast and wide
Containment protects the customer's line while you investigate. It must cover every place suspect parts could be:
- At the customer — stock at their incoming store and line side. Often this means sending a sorting team, or paying a third-party sorting agency the customer nominates.
- In transit — dispatches on the road or at a warehouse.
- In your finished-goods store — packed lots from the same period, machine or material.
- In WIP — parts at the relevant operations.
- At job-work vendors, if an outside process could be involved.
With traceable records, you can answer the question "which lots could be affected?" in minutes: the defective lot was made on press 7 in the second shift on these dates, from coil heat number X, and these other lots share those conditions. Without them, the safe answer is "everything from the last month", which means much more sorting.
Record the sorting results: quantity checked, quantity found defective and where. These figures are needed for the 8D and are also evidence if the customer's debit note is disputed.
Step 3: Returned material and debit notes
Rejected parts may be returned, scrapped at the customer's end, or reworked on site. Each route has paperwork:
- Returns come back on the customer's document and should be received on a separate GRN as customer returns, inspected and dispositioned — rework, scrap or use — not mixed into stock.
- Debit notes from the customer cover rejected parts and often sorting charges, line stoppage or administrative charges according to the supply agreement. Each one should be linked to the complaint, checked against your own sorting records, and accepted or disputed promptly.
- Replacement supply must be planned urgently and may disrupt the production plan.
Many suppliers only discover the true cost of a rejection months later, when accounts finds debit notes no one has matched. Linking debit notes and sorting costs to each complaint gives the real cost of poor quality by customer and defect — which is often the strongest argument for investment in prevention.
Step 4: Root cause
With the parts contained, the investigation starts from the production records behind the defective lot:
- Which machine, die or mould, operator and shift made it.
- Which material heat or lot was used.
- What the in-process and final inspection records show for that lot.
- Whether there were setups, tool changes, breakdowns or parameter changes during the run.
- Whether the same defect has appeared before, internally or at another customer.
Every 8D needs two root causes: why the defect occurred, and why it escaped your inspection. The second is often more important to the customer, because it shows whether your detection is reliable. Use 5 Why analysis for each.
Step 5: Corrective and preventive action
Actions should address both causes — for example a die maintenance interval shortened (occurrence) and a check added at final inspection with a go/no-go gauge (escape). Each action needs an owner, a due date and evidence that it was done and works: before-and-after data, photos, updated documents. Actions should also be applied across similar parts and processes, not just the one that failed. This "horizontal deployment" is something OEM quality engineers increasingly check for.
Step 6: The 8D report
Most OEMs have their own 8D format and submission portal. The content is the same: team, problem description, containment, root causes, corrective actions, verification, prevention and closure. If complaint, containment, root cause and actions are recorded in your system as you go, the 8D is largely assembled already, and producing it in the customer's format is quick. Keeping it in your system also means the history is available the next time a similar problem appears.
Step 7: Carry the lessons forward
A closed 8D should change something permanent: the control plan, the PFMEA, the inspection plan, work instructions, maintenance intervals or operator training. Linking the complaint to the documents it changed shows the customer — and your own team — that the lesson has been built into the process.
PPM: know your number before the customer tells you
OEMs typically report supplier PPM monthly: parts rejected divided by parts supplied, times one million. Their figure feeds your supplier rating. Calculating it yourself, from your own complaint and dispatch records, has three benefits:
- You can check the customer's figure and raise discrepancies with evidence.
- You can see the trend by customer, part and defect, not just the monthly total.
- You can set internal targets that are stricter than the customer's.
Track internal rejection rates alongside customer PPM. A rising internal rejection rate on a part is an early warning of customer rejections to come.
What software changes
A quality management system linked to production and dispatch records changes the speed of every step:
- Complaints logged once, with the customer's reference, photos and deadlines.
- Suspect lots found from lot codes in minutes, with their machines, material and inspections.
- Containment and sorting results recorded on tablets, wherever the sorting happens.
- Returns received separately and debit notes linked to complaints.
- Root cause, actions and verification tracked to closure with owners and dates.
- 8D content assembled as you go, and PPM calculated automatically.
The foundation is lot traceability: if every packed lot can be traced back to its production and material, every rejection becomes smaller and faster to resolve.
A worked example
A tier-2 supplier of pressed and welded brackets receives a line rejection from a two-wheeler OEM: 40 brackets with a missing weld nut in a delivery of 2,000. The packaging label carries a lot number. Within half an hour the quality engineer can see that the lot was welded on one of three projection welding stations during a night shift, that the same station produced two other lots, one still in the finished-goods store and one in transit, and that the in-process check frequency for that operation was one part per hour.
Containment is therefore three lots, not a month of production. The occurrence cause turns out to be a worn nut feeder that occasionally misfed; the escape cause is the hourly check, which could not catch an intermittent fault. Actions: feeder maintenance added to the preventive schedule, and a sensor check for nut presence added at the station, with a check sheet entry as interim containment. Both actions are applied to the two other stations. The 8D is submitted on time, and the debit note matches the sorting records.
Know what your supply agreement says
Most OEM supply agreements and supplier quality manuals spell out how rejections are handled: the response time for containment, the deadline for an interim and a final 8D, who pays for sorting and at what rate, how line stoppages are charged, how returned material is handled and how PPM feeds the supplier rating. Many suppliers only read these documents in detail after a costly rejection. Keeping the key terms for each customer — deadlines, charges, report formats and contact people — alongside the complaint record means the quality team knows the rules at the moment they matter, and accounts can check each debit note against them.
Field failures and warranty returns
Field failures — parts that fail in vehicles already sold — are rarer than line rejections but much more serious. The OEM may return failed parts from dealers, ask for analysis within a tight deadline and, in serious cases, ask for the population of affected parts to be identified for a recall or service campaign. Here traceability matters most: the supplier must be able to say which production period, material heats and process conditions the failed parts came from, and which other dispatches share them. Records kept for years, not months, are essential for parts with long service lives.
Preparing for the supplier quality engineer's visit
After a significant rejection, the customer's supplier quality engineer often visits to review containment, root cause and actions on the floor. A visit goes well when the supplier can show, rather than describe: the complaint and its timeline, the sorting records, the production and inspection records for the affected lots, the analysis behind the root causes, the actions taken with evidence and the updated control plan and work instructions at the station. Having these in one system — not in email threads and folders on different PCs — makes the difference between a defensive meeting and a confident one.
Building a prevention habit
Suppliers with consistently low PPM tend to share some habits. They review internal rejections daily at the start of the shift, they treat internal defects with the same seriousness as customer complaints, they share lessons from one customer's complaint across all similar parts, and they track the cost of rejections in rupees so that prevention competes fairly for investment. None of these require sophisticated software, but all of them are much easier when rejection data is recorded at the point of inspection and reported automatically, rather than compiled by hand once a month.
Working with Corposol
Corposol builds custom quality management software for Indian auto component suppliers and other manufacturers — inspections, NCR, CAPA, customer complaints and traceability — as part of our manufacturing software work. Read our use case for an auto component supplier. All custom code is transferred to you on final payment.
Frequently asked questions
What should a supplier do first when an OEM rejects parts?
Contain. Identify all suspect stock — at the customer, in transit, in your finished-goods store and in WIP — and sort or hold it, usually within hours. Root cause comes after containment, not before.
What is PPM in customer quality?
Parts per million rejected: the number of parts the customer rejected divided by the number of parts supplied, multiplied by one million, usually reported monthly. Many OEMs use it in supplier ratings.
How does software help with customer rejections?
It links the complaint to the lots shipped, the production records and inspections behind them, tracks containment and 8D actions to closure, records returned material and debit notes, and calculates PPM by customer and part.
Does recording rejections help with supplier ratings?
Your own records let you check the customer's figures, respond quickly and show trends improving. They cannot guarantee a rating, which depends on the customer's own system and your performance.
