Manufacturing & custom software · Bengaluru · Whitefish, USA
Manufacturing

Connecting MES and Tool Management: Tool Life Counted From Production

How linking shop-floor production booking with tool and die records gives automatic tool life counting, tool readiness checks before jobs start, tool-related rejections, setup records and tool cost per part.

By Corposol Team··9 min read
Hot workpiece between the halves of a drop forging die
Photo: Drop forging Gesenkschmieden by F. Broer, CC BY-SA 3.0 (cropped)

Tool management and production tracking are often separate worlds. The toolroom keeps a register of dies and moulds, with maintenance and repairs recorded when someone remembers. Production records output on job cards or in an MES. The link between them — how many strokes a die has run, how many shots a mould has made since its last service — is calculated by hand, estimated, or not known at all.

Connecting the two removes most of the effort and most of the guesswork. When the MES knows which tool is on which machine for each job, every production booking also counts tool life. This guide explains how the connection works and what it makes possible for tool and die management.

Without a connection, tool life is managed in one of three unsatisfactory ways:

  • By calendar — the die is serviced monthly whether it ran 2,000 strokes or 200,000.
  • By the operator's memory — "it's been a while, the burrs are getting worse".
  • By a separate register — someone copies counts from production records into a tool register, often days late.

Each leads to tools serviced too early, too late, or after they have already produced bad parts.

How the connection works

  1. Every managed tool has an identity — a number and a QR tag on the die, mould or fixture.
  2. The routing links tools to operations — this part, this operation, needs this die (or one of these dies).
  3. At setup, the tool is scanned on the shop-floor tablet, confirming which physical tool is mounted on which machine for which job.
  4. Production booking counts the tool — quantity produced, divided by parts per stroke or cavities, gives strokes or shots added to the tool's count.
  5. At removal, the tool is scanned off, with its condition — fine, needs attention, damaged — and the last-off parts can be checked.

From these steps, each tool's count since its last maintenance and over its lifetime updates automatically.

Tool readiness before the job starts

Because the routing knows which tools a job needs, the system can check each tool's status before the job reaches the machine:

  • Ready — in its location, within life, maintenance not due.
  • Due soon — close to its maintenance count; the job may finish first, or the toolroom may service it before the run.
  • Under repair or at vendor — the job must wait or use an alternative tool.
  • In use elsewhere — on another machine.

The planner sees this on the plan; the toolroom sees which tools are needed in the coming days. Setups stop being delayed by tools that turn out to be unavailable when they arrive at the press. See our guide to closing the loop between planning and the shop floor.

Maintenance triggered by counts

With counts updating from production, tool maintenance becomes due automatically: sharpen this die every so many strokes, service this mould every so many shots. The toolroom's list of due tools is always current. The MES can warn the operator when a tool on the machine passes its maintenance count during a run — and, if the rules require, ask the supervisor whether to continue or stop. Our guide to press tool maintenance and regrind records explains how intervals are set.

Rejections linked to tools

When rejections are booked against a job, and the job is linked to the tool, rejection data can be analysed by tool:

  • Burr rejections rising as a die approaches its sharpening count — evidence for setting the interval.
  • Flash or short shots on one cavity of a mould — pointing to a specific cavity problem.
  • Higher rejections after a repair — pointing to the quality of the repair or the setup after it.

This turns tool maintenance from habit into a decision based on evidence, and gives quality investigations an immediate lead when a customer complaint involves tooled features.

Setup records and first-off

Every tool mounting is a setup. Recording setup start and end, the setter, and the first-off inspection result against the tool and the job gives several useful things at once: setup time by tool (a target for SMED improvement), a record that the first parts were approved before production continued, and a history of which setter achieves the best results with which tools.

Tool cost per part

When repairs, regrinds, spare sections and toolroom hours are recorded against each tool, and production counts come from the MES, tool cost per part is a simple division. This number is useful for quoting new parts with similar tools, for deciding when a tool should be replaced rather than repaired again, and — for customer-owned tools — for discussions with the customer about tool replacement and amortisation.

Customer-owned tools

Many dies and moulds in Indian supplier factories belong to OEM customers. Customers increasingly ask for the count, maintenance history and condition of their tools. With production-linked counts, this report is available at any time, per customer, and helps support requests for replacement tools before worn ones cause quality problems.

What stays separate

Not every tool needs to be linked to production. Cutting inserts, standard drills and consumables are better managed by type and quantity in the tool crib, with issue against jobs for cost. See our guide to tool crib management. The production link is for tools that have their own life, maintenance and value: dies, moulds, fixtures, special form tools and gauges.

Tools at vendors

Dies and moulds sometimes go out for repair, coating or modification. Sent on a challan and tracked as "at vendor", they show as unavailable in the plan until they return, and their history records the outside work and its cost. Customer-owned tools sent for repair should also be visible to the customer's report.

Rolling it out

  1. Register and tag the tools that matter, with current estimated counts.
  2. Link tools to parts and operations in the routing.
  3. Add tool scanning to setup on the shop-floor tablet.
  4. Let production booking update counts, and compare with any manual records for a few weeks.
  5. Set maintenance intervals and turn on due lists for the toolroom.
  6. Add readiness checks to the plan.

Moulds: shots, cavities and blocked cavities

Injection moulds add their own details. Shot counts drive maintenance, but parts produced depend on the number of active cavities. When a cavity is blocked because of damage, the mould continues with fewer cavities: parts per shot fall, cycle-based capacity changes, and the mould needs repair at the next opportunity. Recording blocked cavities against the mould in the MES keeps production quantities, planned capacity and the toolroom's repair list consistent. Rejections by cavity, where cavity numbers are moulded into parts, point directly to the cavity that needs attention. Our guide to mould maintenance for injection moulding covers mould-specific practice.

Alternative tools and duplicates

High-volume parts often have two or more identical dies or moulds, so production can continue while one is serviced. The routing lists all of them as valid for the operation, and the scan at setup records which one is actually used. Counts then go to the right tool, and the planner can alternate between duplicates to balance wear and schedule maintenance without stopping production. Without the scan, counts for duplicate tools are usually guessed or lumped together, and one tool wears out much faster than the records suggest.

Fixtures and gauges as tools

The same approach works for fixtures and dedicated gauges. Fixtures wear at locators and clamps, and dedicated gauges need calibration. Linking them to operations means the MES can check, at setup, that the fixture is in good condition and the gauge is within calibration. Usage counts from production help set fixture inspection intervals. For gauges, scanning at inspection links each reading to the gauge's calibration status — essential evidence when quality records are audited.

A worked example

A sheet-metal pressing company with around 150 active dies kept die counts in a register updated weekly from production slips. Dies were sharpened when burrs appeared or rejections were raised at the customer. Setups were often delayed because a die was in the toolroom or couldn't be found.

The company tagged its dies, added die scanning to setup on the press-shop tablets, and let production bookings update stroke counts. Within a few weeks, the toolroom worked from a list of dies due for sharpening in the coming days, and the planner saw die status when sequencing jobs. Rejection data by die showed that several dies were being sharpened far too late; intervals were shortened for those and extended for others with consistently low burr. Customers received die history reports on request. The company's experience is described in our use case for a sheet-metal pressing company.

Tool history in customer complaints

When a customer complains about a tooled feature — a burr, a dimension, flash, a missing hole — the first question is which tool made the parts and what condition it was in. With setup scans and production counts, the answer is immediate: the lot was made with die 47 between these counts, which was 80% of the way to its sharpening interval, and the last-off parts after the run showed burr near the limit. That evidence shapes both the containment (which other lots were made late in that die's interval?) and the corrective action (shorter interval, better last-off checks). Without the link, the investigation starts from guesswork.

Toolroom workload from the plan

With tool readiness and due counts connected to the production plan, the toolroom can see its workload for the coming days: tools due for maintenance before their next scheduled job, tools under repair needed by a planned date, and new tools due for try-out. The toolroom foreman can then plan the week instead of reacting to whichever setter shouts loudest. Time recorded on toolroom jobs shows whether capacity is enough, and how much goes on unplanned repairs.

Common mistakes

  • Tracking every insert individually — too much effort for little value.
  • Skipping the scan at setup — then counts go to the wrong tool when several dies can make the same part.
  • Not recording condition at removal — the toolroom then learns about damage only at the next setup.
  • Setting intervals once and never reviewing them — the data exists to improve them.

Measures to watch

Once the connection is running, a handful of measures show whether it is working: the share of setups with a tool scanned, the share of tool maintenance done before the due count rather than after a problem, setup delays caused by tools not ready, rejections attributed to tool condition, and tool cost per part for the main tools. Reviewed monthly by production, toolroom and quality together, they keep the focus on preventing tool problems rather than reacting to them.

In short: one scan at setup, one scan at removal, and production booking that already happens. Those three small steps are enough to give every important tool an accurate count, a maintenance schedule driven by real use and a history that supports quality, planning and costing.

Working with Corposol

Corposol builds custom tool and die management connected to shop-floor production booking, as part of our manufacturing software work for Indian SMEs. All custom code is transferred to you on final payment.

Frequently asked questions

How does MES help tool management?

The MES records which tool, die or mould was used for each job and how many parts or strokes were produced. Tool life is then counted automatically from production, without a separate register.

Can the MES stop a job if a tool is not ready?

It can warn or block when a job is started with a tool that is under repair, past its life or due for maintenance, depending on the rules you set.

Which tools should be linked to production?

Dies, moulds, fixtures and special tools with meaningful life and maintenance — usually individually identified. Standard inserts and consumables are better handled by type and quantity in the tool crib.

Do we need machine counters?

No. Production quantities booked by operators are enough to count tool life. Machine counters add accuracy where they are available.

  • Tool management
  • MES
  • Tool life
  • Die and mould tracking
  • Shop-floor data

Let's discuss your factory's software

Tell us about your process or idea. You'll get a free consultation and a clear, fixed quote — no obligation.

  • Free consultation
  • Prototype before you commit
  • Fixed, itemised quote
  • You own the software

Get a free quote

We reply within one working day. Your details are never shared.